The World's Only Operating Hydraulic Compressed Air Plant
July/August 1978
Dan Steinhoff
New Ashford, Massachusetts 01237
RELATED CONTENT
Eastern Shore Threshermen & Collectors Association Show...
Northwest Pennsylvania Steam Engine and Old Equipment Association...
Oxen were used to snake logs for the Saw Mill and to turn the Horse power''...
Eastern Shore Threshermen & Collectors Association Show...
Gonnerman engine I found on my vacation at Fredericktown, Missouri''...
The town of Cobalt developed in the center of a booming silver
mining area from about 1900 to the late 30s, about 80 large and
small silver mines were in operation. Natives tell the story of the
'Million Dollar Sidewalk', a rich vein was found under one
of its sidewalks, it was quickly relocated and a million dollars
worth of ore was mined from that area. Today one can see idle mine
heads or hoists and tailing or spoil piles in every direction. As
the high grade ore ran out, mine after mine closed. Today, 1976,
only four are active. Now that the price of silver has gone up
making the mining of low grade ore profitable, plans are in
progress for reopening several of the old mines.
Back in 1900 this was a sparsely populated area without any rail
service. Worse, it is hard rock mining so a source of power was a
dire necessity. Plenty of wood was available, so steam boilers and
engines to operate compressors and hoists were hauled in. However,
cutting and processing the wood required manpower badly needed at
the mines. At this point a Mr. C. H. Taylor, a Montreal engineer,
was called in to investigate and produce a central power plant as
coal or rail transport was not available. This ruled out
steam-electric plants. On the other hand, plenty of lakes and
streams are to be found suitable for hydro-electric plants. This
required extensive dam construction and importing of complicated
generating machinery, both difficult at the time. To utilize the
readily available water and construction techniques of the mining
type; shafts and tunnels, Taylor designed a huge 'Tromp.'
This is a method of producing compressed air by utilizing the
gravity flow of water in a pipe formed like a large flat bottom U
or what is called an inverted siphon. Iron workers in the early
years of the iron age knew the principle and used this method to
make air of 1-5 pounds pressure to fire their small forges. It is
simplicity in itself, is fully automatic and available as long as
one has a flow of water. We can see the principle every day. Note
the water draining from a quick draining household sink or tub. It
forms a whirling, funneling action that sucks in air as it flows
downward. Now if this is run horizontally in a size larger pipe and
then upward in the same size pipe as the down pipe it will form an
air cushion in the top section of the horizontal run. If one taps
this section, the air can be drawn off and the flowing water will
release more air while passing through this section. The volume of
air is relative to the head or height of drop. The height of the
riser and the volume of water while the ancient users were working
with a 10' head 2' and 3' pipes and an 8' riser,
Taylor's design used 9' in diameter head shaft and over
300' of head follow the schematic drawing starting at point A.
Twin 16' in diameter heads consisting of 72-14' pipes draw
in the water and air. They are held at the right distance below the
water surface by a pneumatic lift. The two heads are connected to a
9' diameter head shaft, 351' deep. The enlarged tunnel at
the roof section slopes upward to 42' in height at the top of
the air received (see 'B'). It then drops down to tail
shaft diameter, thus the height of water in tail shaft locks in and
controls the psi. of air roughly .434 pounds per foot of height.
The difference in height between A and C is about 50'. This is
to expedite the flow of water through the plant. When the initial
flow was started the top of tunnel and receiver section were pumped
full of air to form the first air cushion. Then as the water rose
in the tail shaft it locked in the air and started working. Since
shortly after 1900 this plant has been in continuous operation to
present time.